2-Piece Floating Rear Brake Rotor Upgrade Kit for Audi C7 S6/S7
The 034Motorsport 2-Piece Floating Rear Brake Rotor Upgrade Kit for the Audi C7 S6/S7 is a complete replacement brake rotor kit, designed to work flawlessly with the factory rear calipers found on the Audi C7 S6/S7 . Weighing in at approximately 13.9lbs, each rotor reduces rotational weight by 3.3lbs on each corner over the factory 17.2lb rotors. While reducing weight, the rotor retains proper thermal mass in the rings to adequately capture heat, while utilizing 72 directionally curved vanes to forcefully flow cool air through the rotor to dissipate heat. Installation Effort: MEDIUMNVH Levels: None - Low
NVH is the measurement of how much noise, vibration, & harshness gets transmitted into the cabin of your vehicle. The 034Motorsport 2-Piece Brake Rotors transfer none to low amounts of noise to the cabin based on user feedback. This NVH is relative to the brake pad installed with the brake rotor. Different brake pads will have different resonances when passing over a rotor with slots, which can sometimes make a slight whirring noise. The sounds from these rotors are the direct result of the performance improvements they make to the braking. The J-slots release gas from under the brake pad, and the high-density directional aero veining in the rotors move substantial air, all resulting in more sounds of air moving. The installation of other suspension components can also affect the NVH transferred. NVH is subjective, so some users may find NVH to be increased or decreased from our rating. If you are experiencing higher than quoted NVH with this product, please email firstname.lastname@example.org for further assistance.
The 034Motorsport 2-Piece Floating Rear Brake Rotor Upgrade Kit for the Audi C7 S6/S7 is a complete replacement brake rotor kit, designed to work flawlessly with the factory rear calipers found on the Audi C7 S6/S7. The factory rear rotors of the Audi C7/C7.5 S6/S7 do not fully use the rotor area available and leave uncontacted portions on the top and bottom of the rotor face. The swept pad area of the rotor is left with 3mm of extra material outside the pad. The 034Motorsport rotor ring design removes the areas of the rotor that are not contacted by the pads, further improving overall efficiency and reducing unnecessary unsprung weight. The result is an overall reduction of rotor diameter from 356mm to 350mm with no loss of braking force, a lighter-weight rotor with improved cooling over OEM.
Weighing in at approximately 13.9lbs, each rotor reduces rotational weight by 3.3lbs on each corner over the factory 17.2lbs rotors. While reducing weight, the rotor retains proper thermal mass in the rings to adequately capture, and dissipate heat
The central hat portion of the 034Motorsport rotor is made of 6061-T6 aircraft specification aluminum. The disc is constructed out of a proprietary metal alloy that can withstand immense braking temperatures while holding form allowing hard street use and long days at the track allowing you to drive versus working on the car. From the factory, the same rotor is used on both sides of the S6/S7, leading to one side having incorrect venting and cooling effects. The 034Motorsport 2-Piece Floating Rear Brake Rotor Upgrade Kit utilizes 72 directionally curved vanes properly oriented for each side of the vehicle to forcefully flow cool air through both rotors to dissipate heat equally.
The face of the 034Motorsport 2-Piece Floating Rear Brake Rotor Upgrade Kit utilizes J-Slot slots to clean the pad and surface of contaminants and allows hot pad outgassing, all while reducing overall braking noise compared to a traditional slotted rotor.
The 034Motorsport rotor and hat floating mount system utilizes high strength alloy steel bobbins. The pins take the load from braking actions while maintaining the axial and radial float between the hat and disc, allowing for safe expansion and contraction from heat.
- Lightweight Construction (13.9lb 034Motorsport Rotor vs. 17.2lb OE Audi Rotor)
- Floating, 2-Piece Design
- Rotor Diameter Optimized for Caliper/Pad Location, Reduced from 356mm to 350mm Overall Diameter
- Aerospace Grade Aluminum Hats
- CM-250 Special Alloy Rotor Rings
- J-slotted Friction Face
- OEM Fitment & Functionality
- 72 Properly Oriented Curved Vanes Force Cooling Air through Brake Disc
- Floating Bobbins Mounting System
- Replaceable Rotor Rings
- Lower Long-term Maintenance Cost
- 356x22mm Specification Left Rotor with 350mm Diameter
- 356x22mm Specification Right Rotor with 350mm Diameter
- Installation and Break-in Instruction Sheets
OE PART INTERCHANGE:
- 4H0 615 601 L
- 4H0 615 601 P
|Audi||A8||2011-2018||D4||6.3L W12 FSI|
The installation of your is a straightforward process that will take approximately 1 hour to complete. You can access our detailed installation guide by clicking the icon on the left.
|Part Number Interchange||4H0 615 601 L|
4H0 615 601 P
- Density Line Control Arm Kit, B8/B8.5 Audi A4/S4, A5/S5/RS5 & Q5/SQ5As low as $790.00
Warning: This product may contain a chemical known to the State of California to cause cancer, birth defects, or other reproductive harm.
Learn More: www.p65warnings.ca.gov